ViewEra V151 User Manual

TFT-LCD VIDEO MONITOR USER MANUAL V151, V172, V191 Video Series www.viewera.com Rev 2.0

9 b. Press “△” or “▽“ to increase or decrease the contrast of the display. Then press “1” to confirm the adjustment and back to OSD main menu. 2) Br

10 3) Sharpness a. Press “△” or “▽“ to move the highlight to Sharpness and press “1” to enter. b. Press “△” or “▽“ to increase or decre

11 4) Color Temperature a. Press “△” or “▽“ to move the highlight to Color Temperature and press “1” to enter. b. Press “1” to select preset co

12 5) User RGB If User is selected, press “△” or “▽“ to move the highlight to Red, and then press “1” to enter the adjustment of R

13 6) Image Press “1” to get the OSD, press “1” then “△” or “▽“ to move the highlight to Image menu, and then press “1” to enter Image sub-menu. Then

14 b. Press “△” or “▽“ to adjust the horizontal position. Then press “1” to confirm the adjustment and back to Image menu. 6.3) V Position a.

15 b. Press “△” or “▽“ to move the vertical position of OSD . Then press “1” to confirm the adjustment and back to Image menu. 6.4) Phase a. Press

16 b. Press “△” or “▽“ to adjust the phase of signal. Then press “1” to confirm the adjustment and back to Image menu. 6.5) Clocks a. Press “△” o

17 b. Press “△” or “▽“ to adjust the clock of signal. Then press “1” to confirm the adjustment and back to Image menu.

18 3.2.1 Audio menu Press “1” to get the OSD, press “△” or “▽“ to move the highlight to Audio menu, and then press “1” to enter Audio adjustment,whic

1 Table of Contents EMC Compliance …………………..……………………………………………………….……...2 Important Precautions ...

19 3.2.2 Feature Controls Press “1” to get the OSD, press “△” or “▽“ to select Feature Controls menu, and then press “1” to enter Feature Controls sub

20 Press “△” or “▽“ to move the highlight to OSD Controls and press “1” to enter. There are three options under OSD Controls: OSD H Position, OSD V Po

21 b. Press “△” or “▽“ to adjust the horizontal position of OSD menu. Then press “1” to confirm the adjustment and back to O

22 b. Press “△” or “▽“ to adjust the vertical position of OSD menu. Then press “1” to confirm the adjustment and back to OSD Control sub-menu.

23 3.4) OSD Timer a. Press “△” or “▽“ to move the highlight to OSD Timer and press “1” to enter. b. Press “1” to adjust the leng

24 3.3 OSD menu in Video mode When OSD menu is not present on the screen, you can press “2” to switch the signal source to c

25 4. Dead Pixel Policy Dead pixels on the TFT LCD panel are sometimes inevitable. ViewEra guarantees that the monitor will be replaced if the number

26 7. Troubleshooting 1) No image  Check if you are using the standard power adapter coming with the monitor.  Check if the power cord is secure

27 8. Specifications a. 15” video monitor V151 Series Panel Type: Screen Size: Pixel Pitch: Brightness: Contrast Ratio: Resp

28 b. 17” video monitor V172 Series Panel Type: Screen Size: Pixel Pitch: Brightness: Contrast Ratio: Response Time:

2 EMC COMPLIANCE This device has been tested and found to comply with the standards for a class B digital device, pursuant to Part 15 of FCC Rules.

29 c. 19” video monitor V191 Series Panel Type: Size: Pixel Pitch: Brightness: Contrast Ratio: Response Time: Viewing

3 IMPORTANT PRECAUTIONS 1. Before using this device, please read all the instructions in this manual carefully. 2. Please keep the manual carefully f

4 Introduction 1.1 General Thank you for purchasing ViewEra’s LCD video monitor which incorporates high quality display, multiple video inputs, and po

5 2. Installation The monitor is equipped with an automatic sensing AC power adapter for a voltage range from 100 to 240 VAC at a frequency

6 2.5 Power on Turn on your monitor and computer. The LED indicator will light green when the screen is under normal condition. If the LED indicat

7 3. User Controls 3.1 Control buttons (3) (4) (5) (6) (1), (2) 1) Power button It is used to turn on or off monitor

8 3.2 OSD menu in VGA mode Press “1” button to enter the OSD main menu. See the Figure as below. Press “1” then press “△” or “▽“ to move the highligh